-
Lap Shear Strength Testing EFP Batch 2 PT C
Lap Shear Strength Testing comparing control (as received-Solvent cleaned only) with E-Form plus pretreated with Henkel pretreatment Process C. -
E-Form Plus Batch 2 Surface Analysis
SEM and GDOES of E-Form Plus mg alloy Batch 2, as received. -
PneumaticBulge 200C Mg e-Form Batch-3 (M12_BBT(PB)-200C)
PneumaticBulge 200C Mg e-Form Batch-3 (M12_BBT(PB)-200C) -
ZEK100 Surface Analysis
SEM and GDOES analysis of ZEK100 Magnesium sheet, as received. -
Shear Testing @ RT Mg e-Form Batch-3 (M12_SH-RT)
Shear Testing @ RT Mg e-Form Batch-3 (M12_SH-RT) -
UniaxialTension PreStraining Mg e-Form Plus Batch-3 @ 200C (M12_UT PreStraini...
UniaxialTension PreStraining Mg e-Form Plus Batch-3 @ 200C (M12_UT PreStraining-200C) -
HydraulicBulge RT Mg e-Form Batch-3 (M12_BBT(HB)-RT)
Hydraulic Bulge RT Mg e-Form Batch-3 (M12_BBT(HB)-RT) -
Plane Strain Testing (for FLC0) at Warm Temperatures of Mg eForm Plus Batch-3...
Plane Strain Testing (for FLC0) at Warm Temperatures of Mg eForm Plus Batch-3 (M12_PST-FLC) -
Mg eForm Plus to Kirksite Heat Transfer Coefficient (M12-Kirksite_HTC)
Mg eForm Plus to Kirksite Heat Transfer Coefficient (M12-Kirksite_HTC) -
Compression of Mg - 0.1Ca (wt.%) 250C - 10 -1, 10 -2, 10 -3 s-1
Compression stress - strain data of Mg - 0.1Ca (wt.%) compressed at 250C at 10 -3 , 10 -2 , 10 -1 s-1 . -
Compression of Mg - 0.1Ca (wt.%) 300C - 10 -1, 10 -2, 10 -3 s-1
A key factor in the limited formability is the strong texture that develops during fabrication of wrought Mg alloys by rolling and extrusion. The predominance of the basal slip... -
Cross-sections of Zn on Zn on scale up pilot line
Large size, 19 x26 inch, sheets plated on the pilot line, qualification for adhesion and thickness. These are cross-section images. -
Cross-section SEM data on AlMn on Zn on Mg
SEM images of thickness and adhesion tests for nanocrystalline Al-Mn coating on Zn on E-form plus, lot 1. -
PNNL Experiments Ontology
This word file describes the scope of experiments conducted at PNNL on Mg ZEK100, Posco E-form Plus and the "new" USAMP Mg alloy sheet. -
PPG Coating over nano-Al over zinc over Mg
Images of salt spray corrosion behavior of test coupons -
Thermocouple Testing Data
Temperature measurement of the sheet for cross form stamping rest to study the temperature drop at actual stamping. -
Stamping Test Videos
Videos of cross Form Tests were conducted on EFORM+ magnesium sheets at 3 temperatures, 175C, 200C, 225C using 2 lubricants, Fuchs and Quaker, and 2 pre-treatments, Henkel and... -
Forming toolset
Experimental tool used for forming test -
Forming Test Bare EFP
Images of ball in cup forming test